Our Upsides of Having a Plumber Install Your Dishwasher

Our Upsides of Having a Plumber Install Your Dishwasher

Blog Article

This Site

From hauling a dishwashing machine into your residence to attaching the water links, installing a dish washer can take up to 5 hours. A plumber will have the right tools on hand and can mount your brand-new dishwashing machine in under two hours.

A Plumber Can Examine the Supply Lines

A supply line, especially a dish washer connector, links the dish washer to a water source. A plumber can make certain that the line is compatible with both your dishwashing machine and water source if you acquire a new supply line. If you determine to use an existing supply line, an expert plumber can check it to ensure that it's in good condition and also does not have any kind of leaks.

An Improper Setup Can Invalidate the Dish washer's Service warranty

Before installing a dishwasher on your own, you should check out the guarantee very carefully. Unless you are handy and have experience mounting dish washers, you must hire a plumber so you do not risk your guarantee.

Mounting a Dishwashing Machine Calls For a Selection of Tools

If you do not have a selection of tools on hand, you might require to make a trip to Lowe's or Home Depot. To install a dishwashing machine, you need the following devices: pliers, an adjustable wrench, a collection of screwdrivers, a tube cutter, as well as opening saws.

Not Mounting Your Dishwasher Correctly Can Lead to a Mountain of Troubles

Not just can setting up a dishwasher properly nullify your warranty, however it can also create a mess. If you incorrectly install your dish washer to the waste disposal, you may notice pungent smells or have deposit on your recipes.

A Plumber Can End Up the Job Affordably as well as Swiftly

You don't want to obtain stuck cleaning your dishes by hand. A plumber can mount your dish washer in one to 2 hrs. Additionally, the ordinary plumber will not bill greater than a couple of hundred dollars to install your dishwasher. Why risk your service warranty as well as possibly need to get a brand-new dish washer? Take the very easy as well as safe path by employing a plumber.
From carrying a dish washer right into your residence to affixing the water links, setting up a dishwasher can take up to five hrs. To make your life less complicated and also to avoid mounting a dish washer inaccurately, we suggest hiring a specialist plumber. A plumber will certainly have the right tools on hand and can install your brand-new dishwasher in under 2 hours. A supply line, specifically a dishwasher adapter, links the dishwasher to a water source. Unless you are helpful and have experience installing dish washers, you ought to employ a plumber so you do not risk your warranty.

How To Install A Dishwasher

Installing A Dishwasher Yourself

Just like other home appliances, a dishwasher helps to make chores less time-consuming and free of hassle. Most modern kitchens have a dishwasher or a cabinet space for dishwasher installation built into them. An older kitchen with no dishwasher or cabinet space for one might require a little reconstruction to accommodate dishwasher installation.

Installing a dishwasher requires basic knowledge of plumbing and electrical wiring. This article contains the steps involved in dishwasher installation, dishwasher installation tips, things to consider when installing a dishwasher in a kitchen that previously had no dishwasher in it, and tips for maintaining a dishwasher.

Steps Involved In Dishwasher Installation

Step One: Gather the Necessary Supplies

Gather all the required items and keep them near the installation site for easy reach. The materials and tools you will require include the following:

A screwdriver

• A hose clamp

• Duct tape (optional)

• A brass fitting

• Teflon tape

• A pair of pliers

• An adjustable wrench

• A drill

• Braided steel water line

• A pair of rubber hand gloves (optional)

• Wire nuts

Step Two: Take Safety Measures

First, turn off the power socket and unplug the power cord if it is a plug-in dishwasher. Then, proceed to turn off the circuit breaker. Next, turn off the hot water shut-off valve under the kitchen sink and run the tap to ensure the water supply is shut off. Protect your kitchen floor close to the installation area with an old rug or a piece of drop cloth.

Step Three: Remove the Old Dishwasher

This step only applies if your kitchen has an old dishwasher that you want to replace. Remove the cabinet door to gain complete access to the old dishwasher. Next, remove the cover of the access panel located at the bottom front side of the dishwasher. Locate the junction box inside the access panel.

Now, unscrew the terminal screws holding the wires in place at the junction box. Then, remove and tuck the wires out of the way with duct tape. Locate the dishwasher water inlet tube, undo the brass fitting and disconnect the water supply pipe from it. Put the disconnected end of the water supply line pipe into a bucket or bowl to collect any water remaining in it.

Reach down beneath the sink to undo the drain hose. Loosen, then clamp and disconnect the drain hose of the dishwasher from the tailpiece of the sink. Next, put the disconnected end of the drain hose into a bucket to collect the water and debris.

With all the connections out of place, remove the screws holding the dishwasher in place with a screwdriver, gently pull the dishwasher out from the cabinet and set it aside. You can use a piece of cloth or towel to clean up the mess made or any water spillage on the floor. Also, clean the cabinet where the old dishwasher was before installing a new one.

Skip this step if you are having a dishwasher installed for the first time in your kitchen.

Step Four: Install the New Dishwasher

Connect the Water Supply

Wrap Teflon tape on the tip of the water inlet pipe located at the bottom of the dishwasher. Screw on the 90 degrees brass fitting to the taped inlet pipe and tighten it with an adjustable wrench. Most dishwasher units do not include a brass fitting, but they are available at hardware stores.

Once you have the fitting, connect the new water supply line to the elbow of the brass fitting. Pass the other end of the waterline through one of the cabinet holes and place it on the floor beneath the kitchen sink.

Attach the Drain Line

Locate the dishwasher drain standout pipe, connect the drain line to the dishwasher, and secure the connection with a hose clamp. Pass the other end of the drain line through the cabinet hole and place it towards the sink drain tailpiece

Slide the Dishwasher into Place

Attach the adjustable legs to the front of the dishwasher. Carefully slide the dishwasher under the countertop into the cabinet. Stop halfway and ensure everything is in a good position before sliding it in completely. Finish hooking up the water line by connecting the other end to the dual shut-off valve located under the kitchen sink.

Proceed to connect the drain hose through an air gap to your garbage disposer, if you have any, or to the drain tailpiece of your sink. If you do not have an air gap, make a high loop with the drain hose before connecting it to the garbage disposal or the sink drain tailpiece.

https://www.movementplumbing.com/blog/how-to-install-a-dishwasher

Schedule

Report this page